Toyota Rear Seat Belt Replacement

Your seat belt must always be in perfect working order for obvious safety reasons. If your rear seat belt has worn belts or broken locks, it should be replaced right away using quality Toyota appropriate parts. Seat belt parts should always exceed ADR regulations, whether you drive a Prius, Landcruiser or another Toyota.

These essential auto parts never need to be modified. SRP’s replacement seat belts are replacement parts that are a perfect fit. Our Toyota seat belts fulfil the factory’s performance and safety requirements. Our seat belts are composed of high-quality materials that will endure just as long as the originals.

SRP is the place to go when you need to replace seat belt parts on your Toyota. When it comes to safety, never compromise. Toyota seat belts and other safety accessories are available now.

Is Your Toyota Seat Belt Stuck?

Step 1:

Pull-on the seatbelt to dislodge it from its auto-locking mode. If the seatbelt is buckled, unlatch it from the cartridge and move it away from the seat to release more of it. Let it go back to its original shape under the seat gradually. The belt may be knotted, twisted, or a jam deep within the mechanism if it does not snap back into position.

Step 2:

With a screwdriver or needle-nose pliers, pry off the plastic covers that hold the seat belt mechanism in place. The belt loop and hardware will be exposed as a result. Suppose your seatbelt is in the back seat, you’ll need to move the seats down to reveal the seat belt mechanism, which is usually hidden beneath the trunk’s floor layer. Raise the floor layer where the spare tire is usually found to gain access.

Step 3:

Completely remove the seat belt. This will reveal any tangles, kinks, or anything lodged in the belt or the seat belt mechanism’s bottom.

Step 4:

If there are any clogs in the seatbelt, untangle it. Furthermore, if any things are lodged within the belt loop or the bottom half of the belt loop, remove them with your fingers or needle-nose pliers.

Allow the seatbelt to return to its original position. Check that the belt releases and locks into position properly. Replace the plastic seat belt system covers or return the back seat to its original position after everything appears to be working properly.

Seat Belt For Toyota Landcruiser 80 Series

The Landcruiser 80 Series was introduced in 1990 to be the benchmark 4WD of the decade.

Seat belts for Toyota Landcruiser 80 series vehicles were designed without airbags. They’re built to AS2596 specifications. An aftermarket seat belt that isn’t authentic. Normally, they come with 7/16 unf bolts. You can find a seat belt for the Toyota Landcruiser 80 series at SRP Auto.

Toyota Land Cruiser Seat Belt Replacement

Seat belts are more crucial than any other element in a car. They safeguard the most expensive cargo in your vehicle… you! When it deals with the significance of seat belts as a life-saving safety element, statistics don’t lie. It is critical not only for the driver and each passenger in a vehicle to wear seat belts but also for the seat belts to be in good working order.

Seat belts that have been worn for a long time or damaged in an accident are not recommended. Seat belts on even relatively new Toyota vehicles with little mileage used to restrain someone during an accident should be changed, regardless of their apparent condition.

What You Need

The first thing you’ll need to replace seat belts is a set of replacement seat belts that are suitable for your vehicle’s make and model. At SRP, you can search for seat belts suited for your Toyota vehicle. To find the ideal fit, all you need is your car’s make and model.

You’ll need a range of tools on hand once your new seat belts come to make the changes. If you need to remove the trim on your vehicle, you’ll need special trim removal tools for the job. To detach attachment bolts and hex head or Torx head bolts, you’ll need a screwdriver (check the screws holding the belt routing trim to establish the proper size and style), ratchet, and specialist socket wrench, depending on your car.

To tighten the belt attachments, you’ll need a torque wrench. Find the recommended torque specifications for your car in the repair manual or another online source. Finally, a flashlight will be required to observe hidden regions and locate the attachment points.

Toyota Front Seat Belt Replacement

A three-point seat belt situated at the front seats is something that all current cars have in common. Both the buckle assembly and the shoulder belt attachment ought to be replaced when replacing the front seat belts. In addition, the opposite side of the seat’s attachment point will need to be changed. To get to the attachment points beneath the centre pillar moulding, you’ll have to remove the trim panel.

Clips hold the trim panels in place. To gently release the panels and locate the clips, use trim removal tools. The same tools could be used to loosen the clips once they’ve been found. With the socket wrench and the right size socket, you may remove pieces that are screwed or bolted on. The new belt should be attached following the belts’ routing. The attachment bolts should be tightened to the proper torque specifications once they’ve been inserted.

The rear seat belts will be put in trucks, vans, and SUVs like the Toyota Land Cruiser in the same way that the front seat belts are replaced. The shoulder belt attachment, on the other hand, is located in the passenger compartment’s headliner. During the removal of the headliner, special care must be taken to avoid damaging the back of the headliner. Another spot where the service repair manual could be useful is in determining the optimal procedure.

Seat belt attachments are located under the bottom of the rear seat in passenger vehicles. The cushion can be removed by pulling the seat toward the back of the car, near the part where the seat sits on the floor. As you press back on the centre of the seat cushion, you should feel the spring tension release. The seat should then be lifted and removed from the car, giving you access to the seat belt. After the belt has been replaced, use the tool to tighten the bolts to the proper torque.

One of the most crucial things you could do to improve the safety of any vehicle is to replace worn or torn seat belts. Damage should never be dismissed as insignificant when it could mean the difference between life and death.

At SRP You Will Find The Best Quality Toyota Seat Belts For Sale

You’ve been putting off your Toyota rear seat belt replacement for a while, but you don’t want to keep putting it off indefinitely. You’ve been looking for the right firm to do this repair for you but haven’t come across anyone you think is worth it until now. SRP sells different seat belt parts Toyota to mechanic workshops and people who have at-home garage projects and are repairing a car themselves. You can always be rest assured that SRP services are top-notch as they have a lot of happy clients who can (and have) attested to the high quality of work they received when working with them